Short answer: Laminate sounds hollow when a thin plank floats over a hard subfloor with nothing to absorb impact. The fix is mass plus padding: a thicker plank and a quality attached underlayment. Two lab numbers — IIC for impact noise and STC for airborne noise — let you compare floors before you buy. Opulux tests at IIC 69 and STC 62 with its 12mm plank and attached 2mm IXPE foam.
Why laminate gets its noisy reputation
A floating floor is a stiff, lightweight panel suspended over a subfloor with an air gap, however thin, beneath it. Strike a stiff panel over an air gap — a heel, a chair leg, a dropped toy — and it behaves like a drumhead. Early laminate earned the "clicky apartment floor" reputation honestly: 7mm planks laid straight over concrete with no underlayment. The category fixed this years ago; the spec sheet tells you whether a given product did.
IIC: the impact number
IIC (Impact Insulation Class) measures how much impact sound — footsteps, drops, furniture scrapes — a floor assembly keeps from transmitting to the room below. Higher is quieter. Building codes commonly require IIC 50 for multifamily construction; anything in the 60s is genuinely quiet. Opulux tests at IIC 69, which is why it clears the acoustic requirements boards and HOAs attach to condo renovations — bring the rating to your board before the install, not after.
STC: the airborne number
STC (Sound Transmission Class) measures airborne sound — voices, television, music — passing through the assembly. It's mostly a multifamily and second-story concern. Opulux tests at STC 62. One honest caveat that applies to every brand's numbers: IIC and STC describe a full lab assembly, including the subfloor and ceiling below. Your building's real construction will shift the result; the ratings are for comparing products on equal terms, not predicting exact decibels in your living room.
The two specs that actually make a floor quiet
- Plank mass. A 12mm plank like Opulux simply has more material to damp vibration than a 7–8mm plank — the difference you hear as a dense, wood-like footfall instead of a clack.
- Attached underlayment. Opulux ships with 2mm IXPE foam bonded to every plank, so the sound pad can't be skipped, wrinkled, or value-engineered out on install day.
- (And one that doesn't:) the AC rating. AC4 describes wear resistance, not sound. A floor can be commercial-grade tough and still quiet — the two specs are independent, and you should check both.
Install details that decide what you hear
The quietest plank still telegraphs a bad install. Three details carry most of the acoustic result: flatten the subfloor (hollow spots under a floating floor become literal drum chambers — stay within roughly 3/16" over 10 feet); leave the specified expansion gap so planks never press the wall and transmit squeaks; and over concrete, use the required 6-mil poly moisture barrier under the floor. Furniture felt pads and a doormat program finish the job — grit underfoot is both the top wear source and a surprising noise source.
Where quiet matters most, room by room
Acoustics aren't evenly important across a house. Upstairs bedrooms and hallways over living space are where impact noise gets noticed — and where an IIC number earns its keep. Condos and apartments make it a compliance issue, not a comfort preference. Home offices reward the dense footfall of a heavy plank during calls. And open-plan main floors benefit less from transmission numbers than from the in-room sound: the difference between a hollow clack and a muted, wood-like step as people cross the kitchen. A 12mm plank with bonded padding improves all four cases with one spec decision.
What a quiet floor doesn't fix
Honest limits: an IIC 69 floor won't soundproof a room. Airborne noise through walls, plumbing noise, and structural creaks in the joists are outside any flooring spec. And no acoustic rating changes the care rules — Opulux still wants spills wiped promptly, no steam mopping, and indoor conditions held at 35–50% humidity and 60–85°F. A quiet floor is a component of a quiet home, not the whole system.
Frequently asked questions
What IIC rating do condo boards usually require?
Most multifamily codes and HOA rules start at IIC 50, with stricter buildings asking for the 60s. Opulux's tested IIC 69 clears the common thresholds — submit the rating with your renovation application and confirm your building's specific number.
Does a thicker laminate always mean a quieter floor?
Thickness helps — mass damps vibration — but the pairing matters more. A 12mm plank with bonded 2mm IXPE foam, like Opulux, outperforms a thick plank over bare subfloor. Check for an attached underlayment and a published IIC number, not thickness alone.
Can I add a second underlayment under laminate with an attached pad?
No — doubling up makes the floor too soft, stressing the click-lock joints as they flex underfoot. With an attached pad like Opulux's, the only thing added beneath is the 6-mil poly moisture barrier required over concrete.
Why does my current laminate click when I walk on it?
Usually one of three things: no underlayment, an unflat subfloor leaving hollow spots, or debris trapped beneath the planks. All three are install-layer problems — which is why a bonded underlayment and honest subfloor prep matter more than any marketing word on the carton.
Hear the difference a 12mm plank with attached IXPE makes — explore collections like Vogue and Aurora in the shop, or find a dealer.
Keep reading
- AC3 vs AC4 vs AC5: Which Laminate Wear Rating Do You Actually Need?
- How Long Does Laminate Flooring Last?
- Best Water-Resistant Laminate Flooring: A 2026 Buyer's Guide
Explore Opulux: Shop all styles · Find a dealer




